Primary tabs
Descaling Scalefoe Compound
RXSOL-16-1008-060 Descaling Scalefoe Compound is a liquid acid containing descaling accelerators, corrosion-inhibitors and wetting agents with acidic Polymer with Phosphoric ACID.
- Unlimited shelf life.
- Easy to rinse off.
- Fast and effective scale remover.
- Removes scale and rust from condensers, evaporators, heat exchangers,Rediator etc.
- Removes water scale from boilers.
The most effective RXSOL-16-1008-060 ,Descaling Liquid - II is accomplished by circulation for large systems or components. In the case of small components, the soak method in an immersion bath can be used.
If the equipment to be cleaned is contaminated by oil, grease, sludge or carbonised oil, then pre-cleaning with Rxsol-20-2002-SC or Rxsol-10-1006-SB is necessary.
Rxsol-16-1008 should alway be used in plastic bucket. RXSOL-16-1008-060 should always be added in, never add water in RXSOL-16-1008-060.
RXSOL-16-1008-060 dilute with fresh water as 5-30%, solution depending on scale. Make a circulation system so as to allow the solution to enter through the lowest point and leave through the highest point of the equipment, which is to be descaled.
TIPS for CLEANING
Fill up the whole system with the solution and circulate through a centrifugal pump.
At the initial stages, pH of the solution is generally at 2 to 3 there is an increase in the pH of the solution, during the reaction. The increase in the pH of the solution during circulation reflects on going reaction. Add more quantity of RXSOL-16-1008-060 and continue circulation, in case of the pH level being 4.5 to 5. If circulation of the system shows constant pH 2 to 3 after time confirms the completion of the process of descaling.
For the prevention of further scaling in melting industry, RXSOL-16-1056-025 is recommended.
Why Use RXSOL Descaler?
- It is a safe , economical concentrated chemical to be used on the waterside of heat transfer equipment.
-
You do not have to heat RXSOL 1008 .
RXSOL 1008 is safer for the employees to use than other acid products. -
Your equipment will be cleaned in only hours without disassembling any part of the equipment. Equipment can also be cleaned without any down time (cleaning on the run).
- Cleans down to the original surface without pitting.
- RXSOL 1008 is safe on copper, copper-nickel, bronze, brass, iron, stainless steel and rubber.
- RXSOL 1008 will extend the usable life of your equipment, especially when used as a part of a regularly scheduled preventative maintenance program.
- Removing the scale build-up allows your equipment to operate more efficiently with less downtime.
Pooperties:-
|
Appearance: |
Pale yellow or Brown Liquid |
|
|
|
Density, in g/cm3 at 15°C: |
1.2 |
|
|
|
Flash Point, (PMCC) in °C: |
N/A |
|
|
|
pH, in conc: |
< 1.5 |
|
|
|
Compatibility: |
|
|
|
|
Metal: |
Contains corrosion inhibitors, Polymer |
|
|
|
Rubber: |
No known effect. |
|
|
|
Synthetic rubber: |
May swell. |
|
|
|
PACKAGING: |
Product no: |
Size (in litres): |
Container: |
|
|
RXSOL-16-1008-060 |
25/50 |
Plastic |
Do not use concentrated 1008 on aluminium surfaces
Uniqueness of 1008 :: --
Descaling Scalefoe Compound has the ability to dissolve approximately 1.5kg of calcium carbonate scale per gallon in concentrated form. It does not need to be heated up during cleaning. The uniqueness of this Descaler allows you to clean some equipment while still in operation utilizing a minimum of your own personnel.
When the amount of scales increases, the contact area of scale and cleaner is very small and a longer time of dissolution is required. * Calcium sulfate cannot be dissolved by an acid cleaner.
RXSOL-16-1008-060 is a powerful dissolving agent of calcium carbonate. Therefore, it is better to use RXSOL-16-1008-060 to do circulating cleaning at an early stage before the scales build up and block the tube, or regular cleaning is recommended as well. It is impossible to do a circulating cleaning when the tube is completely blocked.
* Calcium sulfate is easier to be formed when the temperature goes higher.