Thermic Fluid Decarbonizer
Thermic Fluid Carbon Cleaning Chemical is a Solvent based Heavy-duty carbon cleaning chemical to dissolves carbon to used as a thermic fluid carbon cleaning chemical. Removes all the carbon deposits inside the system. Carbon Cleaner solvent acts as a powerful Carbon Dissolver. We are keeping ready stock of carbon remover in 25, 50 Ltr packing.
Very effective to clean lube oil filter and also helps to clean and breaks quickly combustion products from fuel heater, oil bath, highly soiled components. blocks, gear boxes, pistons, rings, valves, atomizers, pipes, burners, coolers, cylinder etc.
Technical Specifications
It contains Sodium Tolyltriazole ( CAS No- 64665-57-2 ) which is mainly used as antirust and corrosion inhibitor for metals (such as silver, copper, zinc, lead, nickel, etc..), and for antirust oil (tallow) products, the gas phase corrosion inhibitor of copper and copper alloy, lubricant additive, cycle water treating compound and auto antifreeze. It also can be used with manifold sterilization algaecide and has a very fine corrosion mitigation effect on close cycle cooling water system.
Mineral Oil Compatible, Additive Cleaner for Large Systems, Minimal Downtime
Application & Dosage
USED TO REMOVE HARD CARBON FROM THERMIC FLUID BOILER / HEATER
Solvent based Heavy-duty carbon cleaning chemical helps to dissolves carbon, resin, and varnish deposits quickly. RXSOL Carbon Remover breaks quickly combustion products from fuel heater, oil bath, highly soiled components. blocks, gear boxes, pistons, rings, valves, atomizers, pipes, burners, coolers, cylinder etc.
For removal of carbon deposits it must be used concentrated ,contained in a steel immersion bath.
SAFETY AND HANDLING:- Completely Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running water for 15- minutes and seek medical attention.
carbon remover can dilute with water to makes it economical
carbon remover msds available on request
Its formulation makes it to use as a hard carbon remover
Also very effective to use as a baked carbon remover
carbon deposit remover is very effective to clean diesel engine parts, without scrubbing and harrashing original surface. due to its uniqunness kept this materials in best carbon removal agent
carbon deposit cleaner loosen hard deposit by emulsifying and pentrating formula.
carbon remover solvent is water missicible in nature.
Typical Industrial Use of Thermal Oil Cleaner for Heat Transfer Systems
- Asphalt Processing & Storage
- Engineered Wood & Building Materials
- Chemical Processing
- Industrial Drying Processes
- Install a 60-mesh screen in the Y-strainer to catch any large lumps that break loose.
- Drain the equivalent amount of fluid from the system before adding Thermal System cCleaner.
- Suggested treat rate is 3-12% of system volume (to be mixed with mineral oil/thermal fluid), depending on the degree of fouling. System cleaning should be preceded by analysis of the fluid to confirm suitable treat rate.
- Add Thermal System Cleaner RXSOL slowly using a positive displacement transfer pump and hoses of appropriate temperature range. Either pump Thermal System Cleaner RXSOL cleaner liquid directly into system (near pump suction if possible) or pump into expansion tank and drain into system.
- Allow cleaner to circulate until all loops are at operating temperature. Run system normally.
- Minimum suggested circulating time is 3 weeks, maximum time is 1 year.
- Clean Y-strainer screen as necessary for duration of cleaning cycle.
- To drain cleaner and fluid, shut off heater but allow pump to circulate until system temperature is cool enough to handle (200°F). Do not turn off pump and allow system to cool as this will permit particles to settle out and contaminate the new fluid.
- Drain system with pump running. Continue to run pump until it begins to cavitate or the low-pressure switch shuts it off.
- Continue draining as quickly as possible. Any delay will allow sludge to settle out in the piping where it will contaminate the new fluid.
- Fill system with a compatible brand and restart system normally.
- One week after startup, send sample to fluid supplier for testing.