Primary tabs
PRELOAD Slip HOLD BLOCK
Polymer BASED non reactive coating materials which makes thin film barrier on surface after dry. Due to formation of RXSOL THIN barrier film on surface, the cleaning operation after unloading becomes quicker and easier with optimum results.
Polymer based Hold coating product, Easy to apply on SHIP HOLD SURFACE. Slip Barrier Coats HOLD BLOCK is POLYMER BASED non-reactive coating materials which makes thin film barrier on the surface after dry. Due to the formation of RXSOL THIN barrier film on the surface, the cleaning operation after unloading becomes quicker and easier with optimum results.
PRELOAD Slip HOLD BLOCK Application Procedure
Before application, previous cargo residues should be completely removed, and the existing paint/coating on the surface should be properly cured.
Application guidance recommends using suitable low-pressure spraying equipment. Application should begin at the bottom of the bulkheads and proceed upward, followed by the tank sides and tank tops. The nozzle is positioned approximately half a metre from the surface during application.
The stated coverage is approximately 16–18 m² per litre, depending on application conditions and surface characteristics. After application, the coating should be allowed to dry completely before loading cargo. Typical drying time is approximately 1–2 hours, depending on temperature and humidity.
RXSOL HOLD BLOCK is a Heavy Duty protective Solution for hold of vessels , which carrying corrosive and / or messy cargos such as sulphur salt petcock coal and concentrates. It can be easily removed with it
General Recommendation Dose for smooth surface :
for Sulphur, Salt, etc 100 Ltrs/Hold for HANDYMAX & 150 Ltrs/Hold for PANAMAX
& for Petcoke, Coal, etc 200 Ltrs/Hold for HANDYMAX & 250 Ltrs/Hold for PANAMAX
This materials can be use directly with low pressure machine or manually by garden spray pump. in general practice on smooth & clean surface each drums of 210 ltrs covers 2000 to 2500 sq meter while on rough and rusted surface require more quantities of materials.
for HANDYMAX (5 Holds) : In general 500 Ltr to 1000 Ltr RXSOL-22-2210-210 require to cover area up to 12 mtrs , i.e approx 1/2 drum to 1 drum of material is sufficient for each hold , while
for PANAMAX (7 Holds) : In general 1000 Ltr to 2000 Ltrs RXSOL-22-2210-210 require to cover full area. , i.e approx 3/4 drum to 1.25 drums of material is sufficient for each hold.
Refer this link for complete set of HOLD CLEANING KIT ::: http://rxmarine.com/Ship-hold-cleaning-kit-set-supplier
This Emulsion is safe to use , But as a precaution goggles & Protective gloves with mask require before use of this materials.
Precaution : 1 > Deposition of previous cargo / Lime wash should be removed .
2 > Newly Painted surface should be fully cured.
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
Technical Properties
PRELOAD Slip HOLD BLOCK as a clear, pale liquid. Published technical information lists a specific gravity around 1.00–1.02 g/cm³ and a pH in the approximately 6.5–7.5 range, with some editions specifying slightly different test conditions. Always refer to the latest product technical data sheet for the specification applicable to the supplied batch.
- Product metal against corrosive cargo
- Products paint against cargo penetration
- Environmentally friendly
- Safe to use in occupied / covered areas
- Reduces turn around times
- Easy to direct spray
- If hold cleaning is to be performed from tank top level only powerful equipment designed for cargo hold cleaning will do the job in a minimum of time.
- Effective cleaning chemicals that can dissolve stains and remove discoloring are required the crew needs to have effective equipment to apply these chemicals from tank top level personal proactive equipment is required depending on type and condition of hold paint chemical that protect the paint may also be needed
- And don’t forget procedures have to be drown up and your
- Crew trained for the job Standardization of equipment and chemical onboard you ship will make life easier for your seaman and save your time
Refer this link for complete set of HOLD CLEANING KIT ::: https://rxmarine.com/Ship-hold-cleaning-kit-set-supplier