Primary tabs
Hold Wash Concentrate RX
RXSOL HOLDWASH is a versatile all-purpose QUALITY marine cleaning solution. It can be used as a powerful stand-alone cleaner for oily stains and residues, or in combination with RXSOL HOLDWASH as a barrier remover.RXSOL hold wash is a versatile all purpose marine cleaning solution it can be used as a powerful stand alone cleaner for Petroleum oily stains and residues, vegetable and animal fats, as well as dirt, proteins, soils, coal, ore, coke or in combination with RXSOL hold wash as a barrier remover.
FEATURES & BENEFITS :-------------------
1> Non toxic , 100% biodegradable, Environmentally friendly
2> Heavy duty Hydrocarbon remover
3> Non caustic Safe to use in occupied / covered areas
4> Safe on skin , Can be easily applied by ship's crew
5> Can be diluted to suit cleaning needs
6> Reduces turnaround times
7> using an RXSOL Application Set
Depending on contamination 50 - 200 ml per 10 litrs of water . i. e. 200 mol to a bucket of water .
Method of Application and Dose Rates:
1.Direct injection method for washing machines. Dose rate 1-5 litres per ton wash water (0.1-0.5%).
2.Recirculation method. Dose rate 1-7 litres per ton wash water (0.1-0.7%).
3.Spot cleaning. Hand spray neat or diluted with up to Five parts water and leave for several minutes before rinsing off with clean water.Cleaning of Cargo Tanks to remove Soot from Inert Gas Systems.
5.Spray RXSOL-22-2204-210 on with a high pressure cleaning machine and use1:6 with water.If used with hand sprayer,spray the product neat onto the surface,allowing1 lit.for every12 m2.Use a5-8%solution in a tank washing machine.
6.Leave for about 30-45 minutes.The surface should be kept wet.
7.Wash down with hot water (80°C) and check the cargo tank
8.Repeat the procedure if necessary.
Note: Whenever possible,the cleaning solution should be heated to 60-80°C.If this method is not possible,other conventional methods such as separate rate direct injection,recirulation or hand spraying provide acceptable options.For boiler fire side cleaning,a 10-20 % hot solution, (temp.above 40°C),should be sprayed on to the surfaces to be cleaned.Allow to penetrate for 20 minutes and flush off. For deposits which are very hard to remove, increase the concentration to 50% and repeat if necessary
The use of RXSOL-22-2204-210 in correct dosages is half the job done.
FOR HOLD CLEANING :::
For Light cleaning 10 - 50% solution with water
For Moderate deposits 50 - 75% solution with water
For Heavy deposits 75% solution with water
3 Pieces of Good Advice
Apply RXSOL-22-2204-210 on dry surface where possible. A dry surface will absorb far better than a wet surface. Allow the product to soak for 10 - 30 minutes. Due to the wetting agents, emulsifier will stick to the wall longer, thereby increasing the contact time, resulting in a better cleaning effect.
When applying RXSOL-22-2204-210 on vertical surfaces: Start application from the bottom and work upwards! If beginning from the top and going downwards, the RXSOL-22-2204-210 may produce "channels" down the surface, thereby running too fast off the surface.
Make sure the solution on the wall doesn’t dry on the surface. Rinse the tanks by means of high pressure waterjetting. This removes the cleaning solution
including the residues.
During high pressure cleaning:It is important that the rinsing water does not run over non-cleaned surfaces! The rinsing water can draw cleaner from the surface if running over non-cleaned surfaces. High pressure together with optimum concentration of RXSOL-22-2204-210 will give the best effect.
Features & Benefit:-
- Heavy duty hydrocarbon remover
- Can be diluted to suit cleaning needs
- Environmentally friendly
- Safe to use onto the occupied areas /covered areas
- Reduces the turnaround times
- Cam be easily applied by ship’s crew
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
RXSOL has the wide range of chemicals for cleaning chemicals for any type of vessel Including those carrying coal petcock & related to get the cargo hold clean for the next cargo choice of suitable cleaning chemical is essential & very important when applied the chemical resident type apply as important role as a surface active agent need time to penetrate & to take outside particular from the hold surface
25 / 210 Ltrs
Refer this link for complete set of HOLD CLEANING KIT ::: http://rxmarine.com/Ship-hold-cleaning-kit-set-supplier