Primary tabs
BIOCIDE 6111
BIOCIDE 6111 is a broad-spectrum, oxidizing biocide approved for use in recirculating cooling towers, closed loop cooling systems, air washers and brewery pasteurizers.
BIOCIDE 6111 is a powerful microbiocide which will control a wide range of troublesome microbes in both open and closed water systems.
Biocide can be used to control sulfate-reducing bacteria, slime-forming bacteria
BIOCIDE 6111 can be used in industrial process water systems for the control of microbial and algae growth. Examples of these systems include but are not limited to: Air Washer Systems, Recirculating Closed Cooling Water Systems, Process Water Systems, Brewery Pasteurizers, Dairy Sweetwater Systems, Hydrostatic Sterilizers, Packaging Pasteurizers, and other industrial process water systems.
DOSAGE AND FEEDING BIOCIDE 6111 should be fed via a closed feed system (a closed feed system being defined as a system in which fluid is moved from a closed storage vessel into a treated media without exposure to the atmosphere). For complete dosage and feeding recommendations, consult your RXSOL sales engineer.
For typical microbiological control, use BIOCIDE 6111 at a concentration of 5 to 25 ppm based on the total system volume. Higher or lower dosages may be required depending on the specific system conditions.
AIR WASHER SYSTEMS
For use in industrial air washer systems, add BIOCIDE 6111 for Air Washer Systems at the makeup to the air washer sump or chill water sump. For continuous or intermittent use, treat with 10 to 100 ppm of this product depending on the severity of the microbial contamination and the frequency of treatment. Maintain 1 to 5 ppm of active bromine residual.
HEAT TRANSFER SYSTEMS
Recirculating and One-Pass Cooling Water Systems: Add BIOCIDE 6111 for Heat Transfer Systems directly to the cooling water system at a point of uniform mixing, such as the basin area, the sump area of the cooling tower, or other reservoir. Depending on the severity of the problem, a dosage of 10 to 200 ppm of this product (based on total water volume) may be needed. Maintain 1 to 5 ppm of active bromine residual.
FOR PULP AND PAPER MILLS
BIOCIDE 6111 for Pulp and Paper Mills is effective in controlling slime-forming bacteria, fungi, and algae in pulp and paper mill process waters. Add BIOCIDE 6111 directly to the system at a point of uniform mixing. Initial doses of 10 to 100 ppm based on the weight of water in the system should be added as required to maintain control. Repeat treatment as necessary.
FOR WASTEWATER TREATMENT SYSTEMS
BIOCIDE 6111 for Waste Water Treatment Systems is used to control microbial growth in wastewater treatment systems, including sewage systems. Add BIOCIDE 6111 at a point in the system where uniform mixing will occur. The dosage will depend on the severity of the contamination but is typically 10 to 100 ppm. Repeat treatment as necessary to maintain microbial control.
FOR SHELL EGG PASTEURIZER
For use in controlling bacteria and fungi in shell egg pasteurizing operations, add BIOCIDE 6111 for Shell Egg Pasteurizer directly to the water in the pasteurizer at a point of uniform mixing. Apply at a concentration of 5 to 10 ppm based on the total water volume. Maintain a residual of 1 to 5 ppm of active bromine during operation. Adjust dosage as needed to maintain control and follow all local, state, and federal regulations.
NALCO 7330 must be applied according to appropriate national and local regulations. NALCO 7330 is registered for use in the United States. As with all biocides applied in the United States, NALCO 7330 is regulated by the U.S. EPA under the Federal Insecticide, Fungicide and Rodenticide Act (FIFRA). It is a violation of federal law to use this product or any biocide in a manner inconsistent with its product label. U.S. EPA Registration Number 1706-153 is approval for NALCO 7330 use in: Industrial Cooling Tower Systems and Process Water Systems Industrial Recirculating Closed Loop Water Cooling Systems Air Washer Systems and Brewery Pasteurizers Pulp and paper mill influent water systems (but note this use is not currently authorized in California) NALCO 7330 is registered for use in Canada. The federal legislative authority for the regulation of pesticides in Canada is the Pest Control Products Act. As with all biocides applied in Canada, the use of NALCO 7330 is subject to Federal regulation and regulation under provincial/territorial authority. The Pest Management Regulatory Agency (PMRA) administers the Pest Control Products Act (PCPA) for the federal Minister of Health. Canadian PCPA Registration Number 17338 is approval for NALCO 7330 use in: Industrial Recirculating Cooling Water Systems Industrial Process Water Systems. This control product is to be used only in accordance with the directions on the product label. It is an offense under the Pest Control Products Act to use a control product under unsafe conditions. Please refer to the product label (U.S. or Canadian) for specific directions of use (including initial dosage and subsequent dosages, and other detailed, product-specific information ). Product labels can be accessed in the Nalco EH&S (Environmental Health and Safety) database. Refer to the Material Safety Data Sheet (MSDS), SECTION 15 for the most recent information on approvals.